Bộ hiển thị lực - F372A (Unipulse Việt Nam)

Giá: Liên hệ

Bộ hiển thị lực kỹ thuật số với màn hình cảm ứng / hiển thị hình họa LCD: F372A
Nhà sản xuất: Unipulse - Nhật Bản.

Tài liệu tham khảo: F372A force indicator.pdf
* Sự thay đổi số lượng vật chất, mà chỉ có thể nhận biết bằng hiển thị số, được hiển thị dạng sóng.
* Nhiều chức năng giữ mà cho phép giữ một điểm chính xác và chức năng đánh giá OK/NG 
* Chức năng giữ kép có thể thực hiện 2 loại giữ đồng thời bao gồm giá trị trước so sánh và giá trị liên quan.
* Thực hiện cài đặt dễ dàng bằng cách chạm trực tiếp vào màn hình cảm ứng
* Kích thước vuông DIN 96 
* Mạch số tốc độ cao với khả năng thực thi 2000 lần/ giây (max) 

Specifications

ANALOG SECTION
Excitation voltage10V, 2.5V DC
Output current: within 120mA
4-wire (Up to four 350Ωload cells can be connected.)
Signal input range-3.0 –+3.0mV/V
Accuracy
  • Non-linearity: within 0.02%/FS ±1digit (at 3.0mV/V input) 
  • Zero drift: within 0.5μV/℃ RTI 
  • Gain drift: within 0.01%/℃
Analog filter
  • Low pass filter (-6dB/oct.) 
  • Selectable at 30, 100, 300, 1000Hz
A/D converter
  • Speed: 2000 times/sec.
  • Resolution: 24bit (binary)
  • Effective resolution: 
  • Approx. 1/30000 - 3.0mV/V input
Analog monitor output Output level: Approx. 2V per 1mV/V of input LoadLoad resistance: 2kΩ or more
 
DISPLAY SECTION
Display unitTFT color LCD module 3.5 inch
Display area71 (W) mm×53 (H) mm
Dot structure320×240dot
Measured value

5digits: -99999 - +99999
Sign: Minus sign on most significant digit

 
SETTING SECTION
Comparison functionsHH, Hi, Lo, LL, Hysteresis, alarm Hi, alarm Lo, near zero, comparison timing, comparison output selection
Hold settingHold mode, detection start level, detection time, level detection condition, sample point shift value, detection end level, average sample number, inflection minimum slope, Inflection front slope time, Inflection Removal Value, Detection Start Condition, Relative Minimum Count , Relative magnification
Graph setting Graph mode, Y-axis (load) start point, Y-axis (load) end point, X-axis (time) end point, plotting start level, interval time, plotting start level conditions
Calibration setting Excitation voltage, zero calibration, equivalent input calibration, actual load calibration, calibration value selection, unit, minimum scale, digital offset, digital zero limit
Operation settingDigital filter, analog filter, backlight lighting time, language change, SI/F print, motion detect, zero tracking, monitor output filter, display color of measured value, B5 function selection, B6 OFF detection standby time, B8 OFF detection standby time, measured work input change, control input change, password
RS-232C settingCommunication mode, baud rate, character length, stop bit, parity bit, delimiter, flow control
Extended comparison functionPrevious value comparison, relative value comparison
Extended hold functionDouble hold, auto reset change, hold value update, sample trigger change, hold cancel at DZ, hold END timing
Extended graph functionpre-trigger display
Extended operation functionDigital filter characteristics, average time at DZ, RUN output format
Extended optionBCD output data format
 
HOLD FUNCTION
1) Sample 2) Peak 3) Valley 4) P-P 5) Average 6) Inflection Point 7) Relative Maximum 8) Relative Minimum 9) Relative Difference 10) Sample&Peak 11) Sample&Valley 12) Sample&P-P 13) Sample&Average 14) Sample&Inflection Point 15) Sample&Relative Maximum 16) Sample&Relative Minimum 17) Sample&Relative Difference 18) Peak&Valley 19) Peak&P-P 20) Valley&P-P 21) Average&Peak 22) Average&Valley 23) Average&P-P 24) Relative Maximum&Relative Minimum 25) Relative Maximum&Relative Difference 26) Relative Minimum&Relative Difference
 
COMPARISON FUNCTION
Higher Hi (HH) limit setting, Lower Lo (LL) limit setting, High (HI) limit setting, Low (LO) limit setting
 
CALIBRATION VALUE SELECTION
Stores up to 4 types of calibration value that can be interchanged
 
EXTERNAL SIGNAL
External output signal (8 points) HI/LO comparison output (HH, HI, OK, LO, LL) / RUN output / hold end output / graph plotting end output Vce=30V (max),Ic=30mA (max) 
External input signal (10 points)Work selection input / hold control input / digital zero input (DZ) / graph plotting control input / calibration selection input  lc=10mA or lower
 
INTERFACE
SIF2-wire type serial interface
232RS-232C communication interface
BCOBCD parallel data output interface (Option) 
DAVD/A converter voltage output (Option)
DAID/A converter current output (Option) 
ODNDeviceNet interface (Option) 
CCLCC-Link interface (Option) 
 
GENERAL SPECIFICATIONS
Power supply voltageDC24V (±15%) 
Power consumption18W max
Operating conditionsTemperature: operation temperature -10℃ to +40℃ Storage temperature -20℃ to +60℃
Humidity: 85% RH or less (non-condensing)
Inrush current (typ) 55A, 1msec (cold start at room temperature) 
External dimensions96 (W) ×96 (H) ×138 (D) mm (protruding areas are not included) 
WeightApprox.1.0kg
CE marking certificationEMC Directives EN61326-1
 
ACCESSORIES
FCN series I/O connector (with cover)1
Operation manual1
BCD output connector (when BCD output option is installed)1
Mini driver (when D/A converter option is installed)1
DeviceNet connector (when DeviceNet option is installed)1
CC-Link connector (when CC-Link option is installed)1

Option

ModelDescription
BCOBCD parallel data output interface
DAVD/A converter voltage output
DAID/A converter current output
CCLCC-Link interface
ODNDeviceNet interface
 
 

Optional accessories

Model Description
CA372-I/O3m end treatment 24-leads cable with FCN connector at one end
CA81-232X1.5m miniDIN-D-Sub9p cross cable
CN50FCN series I/O connector (with cover)
CN55FCN series I/O connector (with diagonal cover)
CN60Circular DIN 8p connector for RS-232C
CN51BCD output connector
CN71CC-Link connector
CN80Analog I/O connector terminal
CND01DeviceNet connector
GMP96×96Rubber packing
TSU03Lightning surge unit, DC specification