Bộ hiển thị lực - F350 (Unipulse Việt Nam)

Giá: Liên hệ

Bộ hiển thị lực kỹ thuật số kích thước DIN 96 với 2 kênh đầu vào: F350
Nhà sản xuất: Unipulse - Nhật Bản.

Tài liệu tham khảo: F350 force indicator.pdf
* Tính toán và đánh giá các đầu ra có sẵn với 2 kênh đo giá trị biến dạng các loại cảm biến
* Các chức năng tính toán (ch1+ch2, ch1-ch2, |ch1-ch2|, Lựa chọn cao, lựa chọn thấp) 
* 9 đầu ra đánh giá các điểm được trang bị
* Tốc độ lấy mẫu lên tới 3000 lần/giây mỗi kênh.
* Chức năng hiệu chuẩn đầu vào tương đương cho phép hiệu chuẩn chỉ với các phím ấn đầu vào liên quan đến giá trị của một cảm biến.
* Xuất tín hiệu giám sát tương tự

 

Specifications

ANALOG SECTION
Number of sensor inputs2 inputs (strain gauge input)
Sensor excitationDC10V, 2.5V ±5% (It depends on the setting.) Output current: within 60mA (2 channels total)
Signal input range-3.0 - +3.0mV/V
AccuracyNon-linearity: within 0.02%/FS ±1digit (at 3.0mV/V input)
Zero drift: within 0.5μV/℃RTI
Gain drift: within 0.01%/℃
A/D converterRate;Selectable from 3000 times/sec and 300 times/sec 
Resolution;24 bits (binary), 1/10000 with respect to 1mV/V
Analog filterLow pass filter(-6dB/oct.) Selectable at 3, 30, 300, 1kHz
Analog monitor outputOutput level: strain gauge input is approx. 2V per 1mV/V 
Load resistance: 2KΩ or more
 
DISPLAY SECTION
Display unitMain display: Character height 14.6mm Numerical display by 7-segment green LED(6-digit)
Sub display: Character height 8mm Numerical display by 7-segment green LED(5-digit)
Indicated valueMain display: 6-digit, ±8.8.8.8.8 -99999 to +99999 Signs: Minus sign on most significant digit
Sub display: 6-digit, ±8.8.8.8.8 -19999 to +19999 Signs: Minus sign on most significant digit
Display frequencySelectable from 3, 6, 13 and 25 times/sec.
Status displayHI/OK/LO/PEAK/HOLD/HI(ch1)/LO(ch1)/HI(ch2)/LO(ch2)
 
SETTING SECTION
Setting itemWork setting (comparison): Calculated value HI limit / Calculated value LO limit / ch1,2 HI limit / ch1,2 LO limit
Work setting (comparison/hold): Comparison function select / Near zero / Hysteresis / Calculation hold function select / Detection time / Average sample number
System setting (calculation/common operation) : MD / SI/F function select / Display frequency 
System setting (ch operation): Digital filter / Analog filter / ZT / D/Z synchronous mode / A/D conversion speed select
Calibration setting (ch calibration): Calibration function select / Zero calibration / Equivalent input calibration / Actual load calibration / Digital offset / Digital zero limit / Alarm HI limit / Alarm LO limit
System setting (BCO option): Output data select / Output rate / BCD/binary select
System setting (232 option): Communication mode / Communication condition / Delimiter
System setting (DAV / DAI option) : Output data select / Zero scale value / Full scale value
Protect/initialize: Setting protect / Key protect / Initialize / Password
Hold sectionSample, Peak, Valley, Average 
Hold section setting (All section・External signal・External signal + Time)
 
EXTERNAL SIGNAL
External input signal (4)hold section control / hold release / digital zero 1 / digital zero 2
Dry contact input circuit (minus common type) Ic=10mA or less
External output signal (11)HI/LO limit comparison (HI (calculation) ・OK (calculation) ・LO (calculation) ・HI (ch1) ・LO (ch1) ・HI (ch2) ・LO (ch2) ) / alarm (ch1) / alarm (ch2) / hold complete / RUN
Open collector output circuit (sink type) Vceo=30V (max) Ic=30mA (max)
Interface
  • SIF:
  • 2-wire type serial interface
  •  
  • 232:
  • RS-232C communication interface(Option)
  •  
  • BCO:
  • BCD parallel data output interface(Option)
  •  
  • D3V:
  • D/A converter voltage output(3ch)(Option)
  •  
  • DAV:
  • D/A converter voltage output(Option)
  •  
  • DAI:
  • D/A converter current output(Option)

 

※Only one option can be installed.

 
GENERAL SPECIFICATIONS
Power supply voltageAC100 to 240V +10% -15% (free power source) 50/60Hz
Power consumption10W max
Operating conditionsOperation temperature: -10 to +40℃ Storage temperature: -40 to +80℃
Humidity: 85%RH or less (non-condensing)
Dimension96 (W) ×96 (H) ×138 (D) mm (Protrusions excluded)
WeightApprox. 1.0kg
CE marking certificationEMC directives  EN61326-1
Safety standard  EN61010-1, EN62311
 
ACCESSORIES
 AC supply cord (Nominal rating 125V) 3m. 1
AC supply cord converter plug for AC supply cord 1
FCN series I/O connector (with cover) 1
Ferrite core 2
Operation manual 1
BCD output connector (when BCD output option is selected) 1
Operating tool (when D/A converter(3ch) option is selected) 1
Mini driver (when D/A converter option is selected) 1
 

Option

ModelDescription
BCOBCD parallel data output interface
232RS-232C communication interface
D3VD/A converter voltage output(3ch)
DAVD/A converter voltage output
DAID/A converter current output
 

 

 

Optional accessories

ModelDescription
CA372-I/OCable with FCN connector at one-end 3m
CAAC3P-B3AC Supply cord 3m
CAAC3P-CEE7/7-B2AC Supply cord (Voltage resistance:250V)2m
CN3P-2P3P-2P converter plug for AC input cord
CN34D-Sub9p connector for RS-232C
CN50FCN series I/O connector (with cover)
CN51BCD output connector
CN55BCD output connector (with diagonal cover)
CN73D/A converter(3ch) connector
CN81Analog I/O connector terminal